Pressure Tanks
Pressure Tank Repair & Replacement in Bellingham, WA
Rapid-cycling pump or spitting faucets usually mean a failed pressure tank. We test and replace it right.
The pressure tank is what keeps your pump from switching on every time you run a tap. When the bladder inside fails, the tank waterlogs, the pump rapid-cycles, and faucets sputter, which quickly burns out the pump if it is not fixed. It is one of the most common well problems we see, and it is often mistaken for a bad pump.
We test the tank pre-charge, confirm whether the tank or the switch is the culprit, and replace a failed tank with one correctly sized for your pump. Getting the tank right protects the pump you already have.
What’s Included
- Pressure tank diagnosis and pre-charge test
- Waterlogged and failed bladder tank replacement
- Correctly sized tank for your pump
- Pressure switch adjustment and replacement
- Fittings, tank tee, and gauge as needed
A rapid-cycling pump is the number one avoidable cause of early pump failure in the wells we service. Catching a waterlogged tank early saves Whatcom County homeowners the far bigger cost of a burned-out pump.
How Whatcom Well & Pump Works
Getting your water back should be simple and stress-free. That’s why we follow a clear, reliable process from the first call to steady water restored.
- 1
Step 1: Call Us When You Lose Water or Pressure
When the taps run dry or your water pressure drops off, give us a call. We know it is an emergency and we move fast.
- 2
Step 2: We Diagnose the Whole System
We check everything, the pump, pressure switch, tank, and wiring, so we know exactly what failed instead of guessing.
- 3
Step 3: We Fix the Real Problem
We repair or replace what actually failed and fix the real problem, not just swap parts to buy a few more months.
- 4
Step 4: We Test & Confirm Steady Water
We test the whole system and confirm you have steady, reliable water before we pack up and leave.
More Ways We Help
Our Other Well & Water System Services
Well Pump Repair
Lost water or weak pressure? We find the real cause, from a worn pump to a bad pressure switch, and get your water flowing again.
Learn more →
Well Pump Replacement
When a submersible or jet pump is worn out, we pull it and set a new pump sized right for your well and household.
Learn more →
Pressure Tank Repair & Replacement
A waterlogged tank makes your pump short-cycle and pressure surge. We swap the tank and set the air charge right.
Learn more →
Well Drilling
Need a new well or a deeper one? We handle drilling and setup for homes on private wells across Whatcom County.
Learn more →
Well Inspection & Water Testing
Buying, selling, or just unsure? We inspect the well system and test your water so you know exactly what you have.
Learn more →
Constant Pressure Systems
Even, city-like water pressure at every fixture, no more drop-off when two taps run at once.
Learn more →FAQs
Frequently Asked Questions
My well stopped giving water. What do I do?
First, check whether the breaker for the well pump has tripped and reset it once. If it trips again or you still have no water, stop and call us. A dead well can be the pump, the pressure switch, the pressure tank, or the wiring, and running the system while something is failing can burn out the pump. We prioritize no-water calls and diagnose the whole system so we fix the real cause.
How do I know if it is the pump or the pressure tank?
They fail differently. A worn pump usually means weak or no water and a motor that struggles or will not start. A failed pressure tank usually means the pump rapidly cycles on and off, or faucets sputter and spit air. A lot of "bad pump" calls are actually a waterlogged pressure tank, which is why we test the whole system before replacing anything.
How long does a well pump last?
Most submersible well pumps run 8 to 15 years, depending on water quality, how hard the pump cycles, and whether it was sized correctly. A pump that short-cycles because of a bad pressure tank wears out much faster. When a pump is near the end, we tell you straight so you are not paying for a repair on a pump that is about to fail again.
Do you do emergency and same-day service?
We prioritize no-water calls because a failed well means no water to the whole house. We carry the common pumps, pressure switches, and tanks so most repairs get done in one trip. Call us and we will tell you honestly how fast we can get to you.
What areas do you serve?
We serve Bellingham and rural Whatcom County, including Lynden, Ferndale, Blaine, Birch Bay, Sudden Valley, Everson, and Deming. Rural properties on private wells are exactly who we work for. If you are nearby, reach out and we will confirm we can help.
Can you drill a new well?
Yes. New well drilling and well deepening are permitted, licensed jobs in Washington, and we handle the permitting, drilling, casing, and sealing to state water-well construction standards, then set up the pump and pressure system so you end up with a complete, working water source.
How much does a well pump repair or replacement cost?
It depends on what actually failed, your well depth, and whether it is a repair or a full pump replacement. We diagnose first, then quote the job up front with a free, no-obligation estimate, so you know the price before any work starts.
Are you licensed, bonded, and insured?
Yes. We are a registered Washington contractor, which means we are licensed, bonded, and carry liability insurance, all of which the state requires. Well drilling additionally requires a licensed Washington water-well driller. It protects you and your property on every job.
Get In Touch
Request Your Free Well Pump Estimate
Tell us about your well or water system and what you are dealing with. We’ll follow up fast with a free, no-obligation estimate, serving Bellingham and all of rural Whatcom County.
- Phone
- 360-685-1659
- Hours
- Mon to Sat 7:00am to 6:00pm
- Service Area
- Bellingham & Whatcom County, WA
Request Your Free Estimate
No obligation. We’ll get back to you fast.